After you got your Raspberry Pi 2 Model B 1GB & B+, you might have enjoyed the open source function and code, but don't forget this, they are also able to interact with external hardware as embedded system. So get this kit, and start it! We also provide pdf files about how to control them, you will have much fun for doing this!
This 40Pin GPIO Extension Board is already soldered and assembled, so buyer just need to plug it in, then there you go!
The Raspberry Pi B+ has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably a good time to upgrade your set up and accessorize using all of the Model B+'s 40 pins.
That's why we now carry the Sintron GPIO Board Plus with Color 40 Pin Ribbon Cable for Raspberry Pi B+.
GPIO 40 Pin Block Pinout
(1) 330 Ohm Resistor x 10
(2) 1k Ohm Resistor x 10
(3) 10k Ohm Resistor x 10
(4) 5mm RGB LED x 1
(5) 5mm Red LED x 10
(6) 5mm Green LED x 10
(7) Electrolytic Capacitor x 5
(8) 10nF Ceramic Capacitor x 10
(9) 100nF Ceramic Capacitor x 10
(10) Active Buzzer x 1
(11) Jumper Cable Wires x 65
(12) Rectifier Diode x 1
(13) Tilt Sensor/Switch x 1
(14) Vertical Slide Switch x 5
(15) 6 x 6 x 4.3 Push Button x 5
(16) Thermistor Temperature Sensor x 1
(17) Tower Pro Micro Servo 9g (SG90) x 1
(18) Potentiometer(Adjustable Resistor) x 1
(19) 400 Tie Points Solderless Breadboard x 1
(20) Light Dependent Resistors(Light Sensor) x 1
(21) New 40-Pin GPIO Extension Board x 1
(22) 40-Pin GPIO Ribbon Cable for B+ & Pi 2 x 1
(23)Sintron Box x 1
For electronic parts, you can also check our store maker-diy.com
Some products show
(1)400 Bread Board
Brand new and high quality.
1 Terminal Strip, Tie-point 300.
2 Distribution strip, Tie-point 100.
ABS plastic material.
Coloured coordinates for easy component placement.
Phosphor bronze nickel plated spring clips.
Size: 8.3cm x 5.5cm - 3.27inch x 2.16inch.
for more informations, you can check here: 1pcs Quality mini bread board / breadboard 8.5CM x 5.5CM 400 holes for Arduino
(2)40-Pin GPIO Extension Board
(1) Specifically designed for Raspberry Pi Model B+.
(2) With this kit you can connect your Raspberry Pi Model B+ 40 pin GPIOs direct to a breadboard.
for more informations, you can check here: [Sintron] 40 Pin GPIO Extension Board with 40 Pin Rainbow Color Ribbon Cable for Raspberry Pi 1 Models A+ and B+, Pi 2 Model B, Pi 3 Model B and Pi Zero
(3)SG90 9G Servo
Connector Wire Length 150mm
Brand new and full packing.
Great for boat, racing car, helicopter and airplane.
Stable and shock proof.
Operating speed: 0.12sec / 60° (4.8V no load).
Stall torque: 1.2 kg / cm (4.8V), 1.6 kg / cm (6.0V).
Operation voltage: 3.5 - 6.0V.
Temperature range: -30°C -- +60°C.
Dead band width: 5usec.
Gear type: nylon gears.
Connector type: Futaba / JR compatible.
Dimensions: 23 x 12.2 x 29mm
Operating Speed (4.8V no load): 0.1sec / 60 degrees
Stall Torque (4.8V): 1.6kg/cm
Temperature Range: 0 to + 55 degree C
Dead Band Width: 10us
Operation Voltage: 4.8 Volts
Recommend Model: Mini Car / Mini Ship / Helicopter & Airplane
Net weight: 13g
Connector wire length: 250mm
for more informations, you can check here: CFsunbird RC Micro SG90 Servo 9g For Arduino Aeromodelismo Align Trex 450 Airplane Helicopters Accessories