After you got your Raspberry Pi 2 Model B 1GB & B+, you might have enjoyed the open source function and code, but don't forget this, they are also able to interact with external hardware as embedded system. So get this kit, and start it! We also provide pdf files about how to control them, you will have much fun for doing this!
This 40Pin GPIO Extension Board is already soldered and assembled, so buyer just need to plug it in, then there you go!
The Raspberry Pi B+ has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably a good time to upgrade your set up and accessorize using all of the Model B+'s 40 pins.
GPIO 40 Pin Block Pinout
(1) 220 Ohm Resistor x8
(2) 1k Ohm Resistor x5
(3) 10k Ohm Resistor x5
(4) 100k Ohm Resistor x5
(5) 1M Ohm Resistor x5
(6) 5.1M Ohm Resistor x5
(7) 5mm RGB LED x1
(8) 5mm Red LED x2
(9) 5mm Green LED x2
(10) 5mm Yellow LED x2
(11) USB Cable x1
(12) 5V Relay x1
(13) Jumper Cable Wires x65
(14) 1602 LCD Display Module x1
(15) Active Buzzer x1
(16) Rectifier Diode x2
(17) Switching Diode x1
(18) Tilt Sensor/Switch x1
(19) 6x6x4.3 Push Button x2
(20) Field Effect Transistor x1
(21) NPN Small Signal Transistor x2
(22) Thermistor Temperature Sensor x1
(23) Tower Pro Micro Servo 9g (SG90) x1
(24) Potentiometer(Adjustable Resistor) x1
(25) 400 Tie Points Solderless Breadboard x1
(26) Light Dependent Resistors(Sensor) x1
(27) New 40-Pin GPIO Extension Board x1
(28) 40-Pin GPIO Ribbon Cable for B+ & Pi2 x1
(29)Sintron Box x 1
For electronic parts, you can also check our store maker-diy.com
Some products show
(1)400 Bread Board
Brand new and high quality.
1 Terminal Strip, Tie-point 300.
2 Distribution strip, Tie-point 100.
ABS plastic material.
Coloured coordinates for easy component placement.
Phosphor bronze nickel plated spring clips.
Size: 8.3cm x 5.5cm - 3.27inch x 2.16inch.
for more informations, you can check here: 1pcs Quality mini bread board / breadboard 8.5CM x 5.5CM 400 holes for Arduino
(2)1602 LCD Modules
Brand new and high quality.
Wide viewing angle and high contrast.
Commonly used in: copiers, fax machines, laser printers, industrial test equipment, networking equipment
such as routers and storage devices.
LCM type: Characters
Can display 2-lines X 16-characters.
Voltage: + 5V DC.
for more informations, you can check here: Backlight Screen With LCD 1602 Display For Arduino Blue Module 1602A 5V
(3)40-Pin GPIO Extension Board
(1) Specifically designed for Raspberry Pi Model B+.
(2) With this kit you can connect your Raspberry Pi Model B+ 40 pin GPIOs direct to a breadboard.
for more informations, you can check here: [Sintron] 40 Pin GPIO Extension Board with 40 Pin Rainbow Color Ribbon Cable for Raspberry Pi 1 Models A+ and B+, Pi 2 Model B, Pi 3 Model B and Pi Zero
(4)SG90 9G Servo
Connector Wire Length 150mm
Brand new and full packing.
Great for boat, racing car, helicopter and airplane.
Stable and shock proof.
Operating speed: 0.12sec / 60° (4.8V no load).
Stall torque: 1.2 kg / cm (4.8V), 1.6 kg / cm (6.0V).
Operation voltage: 3.5 - 6.0V.
Temperature range: -30°C -- +60°C.
Dead band width: 5usec.
Gear type: nylon gears.
Connector type: Futaba / JR compatible.
Dimensions: 23 x 12.2 x 29mm
Operating Speed (4.8V no load): 0.1sec / 60 degrees
Stall Torque (4.8V): 1.6kg/cm
Temperature Range: 0 to + 55 degree C
Dead Band Width: 10us
Operation Voltage: 4.8 Volts
Recommend Model: Mini Car / Mini Ship / Helicopter & Airplane
Net weight: 13g
Connector wire length: 250mm
for more informations, you can check here: CFsunbird RC Micro SG90 Servo 9g For Arduino Aeromodelismo Align Trex 450 Airplane Helicopters Accessories